Skip to content
  • Save $300.00

Black Kitchen Knife Set, Hammered Blades and Leather Roll

Sale price $300.00 Regular price $600.00
On Sale

Shipping calculated at checkout

Low stock

Description

What Is in the Five Piece Set?

Four knives and a carving fork, every blade black coated and hammered across the face, with black micarta handles pinned and spaced in white.

Cleaver, for chopping and portioning
Long slicer with a squared tip, for carving and long draw cuts
Chef knife, for the daily work of the board
Paring knife, for in-hand detail work
Two tine carving fork, matched to the set

Supplied in a leather knife roll.

What Are the Specifications?

Blade material: High carbon steel
Blade finish: Black coating with hammered face 
Handle material: Black micarta, pinned with spacer
Set size: 5 pieces, 4 knives and a carving fork
Includes: Leather knife roll

Estimated dimensions, read from proportions. Confirm before publishing.

Cleaver blade: approx 7 inches
Slicer blade: approx 10 to 11 inches
Chef blade: approx 8 inches
Paring blade: approx 4 inches
Carving fork: approx 7 inches

What Is the Black Coating?

Worth understanding, because not all black blades are finished the same way and the difference shows up in a kitchen faster than anywhere else.

Black finishes on knives come from a handful of processes. Black oxide is a chemical conversion of the steel surface, thin, food safe, and mildly corrosion resistant, but it wears with use. Ceramic polymer coatings such as Cerakote are sprayed and cured, considerably tougher, and also food safe once cured. Thicker sprayed coatings are the ones to be careful with, since they sit on the surface rather than bonding into it and can chip at an edge or a corner.

One thing applies to all of them. Look closely at any coated kitchen knife and the cutting edge will be bright, because the bevel is ground after coating. The coating protects the flat of the blade. The edge itself is bare steel, which is the part that meets wet food. Care below accounts for that.

Why Are the Blades Hammered?

The dimpled texture across the face, called tsuchime in Japanese knifemaking, does a real job besides looking like forge work.

Food sticks to a flat blade because of suction. A wet slice of potato or cucumber lies flush against a smooth surface, air cannot get between the two, and the slice rides up with the knife instead of falling away. Anyone who has chopped a large quantity of anything starchy knows the result.

Hammering breaks the face into peaks and hollows, so a slice only contacts the high points and air sits in the gaps. The suction never forms and the food releases. The same logic drives the dimples on a granton edge, which solves the same problem a different way.

Traditionally the texture was a byproduct of forging rather than a design choice, left in place because smoothing it served no purpose. The function was noticed afterwards.

What Is Micarta?

Layers of fabric, usually canvas or linen, saturated in resin and compressed under heat into a solid block.

For a kitchen handle the relevant property is indifference to water. Micarta does not swell, shrink, crack, or rot, and it needs no oiling, which separates it from every natural wood handle including the stabilised ones.

Grip is the second reason. Micarta has a slightly textured feel that improves rather than worsens when wet, since the fabric layers give the surface tooth. Polished wood and steel both get slick with water or fat on them.

Harder wearing than wood and noticeably tougher than most plastics, which is why it moved from industrial electrical insulation into knife handles in the first place.

Our micarta handled chef set carries the same material in other colours.

Why Include a Carving Fork?

Because a long slicer without one is half a tool.

Carving a roast means the meat has to stay still while the blade draws through it. Holding it with a hand is awkward and unsafe near a long sharp edge. Holding it with a regular fork tends to tear. A carving fork has two long tines set wide, which pin the joint in two places, resist the drag of the blade, and leave a clean lift when the slice comes free.

Most kitchen sets leave it out because it is not a knife and does not help the piece count look impressive. Including one means the slicer in this set can actually be used for the job it was shaped for.

How Should You Care for Coated Carbon Steel?

More specific than general knife care, because a coated blade has two surfaces with different needs.

The edge is bare steel and it will rust. High carbon steel with no coating at the bevel marks within hours if left wet, and acidic food accelerates it. Rinse and dry immediately after every use, every time. Not at the end of cooking, immediately.

Oil the edge before storing. A thin wipe of food grade mineral oil along the bevel. Not cooking oils such as olive or vegetable, which oxidise and go rancid against steel.

Protect the coating. Do not scrub a coated blade with abrasive pads or scouring powder, which will wear it through. A soft cloth or sponge is enough.

Never a dishwasher. Heat, detergent, and a long wet cycle will damage the coating, rust the edge, and knock the blades against racks.

Store the knives out of the leather roll. Leather absorbs and holds moisture against steel, and tanning residues are mildly acidic. The roll is for carrying and transport. Long term storage belongs in a block, on a magnetic strip, or in a drawer with guards.

Do not store them in a sealed plastic bag either. Trapped humidity condenses on the blade and causes the rust it is meant to prevent.

Cut on wood or composite boards only. Glass, stone, and ceramic destroy edges. Sharpening follows our knife sharpening guide.

Safety

Every blade in this set is sharpened to a working edge and shipped ready to cut. Unwrap each one with the edge facing away from you, keep them out of reach of children, and cut on a stable board with the hand not holding the knife tucked back from the edge.

Who Is the Set For?

Cooks who carve, since the slicer and matched fork cover a job most sets ignore entirely. Anyone who does a lot of board work with starchy or wet produce, which is where the hammered faces earn themselves.

Buyers who want handles that need nothing. Micarta tolerates a kitchen better than any wood, which matters if knives tend to end up in a sink in your house.

Cooks who want a set that looks different, since black blades with hammered faces are not a common sight.

Not the right set for anyone who wants a stainless, maintenance-free kitchen, since the bare edge needs drying every time. Buyers wanting forged pattern welded steel should see our hand forged kitchen knives, and the wider range sits in the kitchen knife sets collection.

Why Choose the Black Kitchen Knife Set?

Hammered faces that release food instead of holding it, a carving fork most sets leave out, micarta handles that ignore water entirely, and a leather roll to carry the lot.

Every knife is finished by hand, and we have been making knives since 2001.

Highlights

  • American Express
  • Apple Pay
  • Bancontact
  • BLIK
  • Diners Club
  • Discover
  • EPS
  • Google Pay
  • JCB
  • Maestro
  • Mastercard
  • Multibanco
  • MB WAY
  • MobilePay
  • Satispay
  • Shop Pay
  • Union Pay
  • Visa

Shop with confidence

  • Easy exchanges
  • Trusted reviews
  • Eco materials
Back to top